film recycling technology
Film recycling process:
Crushing, washing, dewatering, drying and granulation
Olefin film mainly includes polyethylene and polypropylene film, which is usually used in the fields of agriculture and packaging. High density polyethylene, low density polyethylene and linear low density polyethylene and polypropylene film (OPP, BOPP, CPP).

For the leftover bits and pieces produced waste film in the production process or the test, because do not contain impurities ,so they can be directly crushing, granulating and recycling. The recycling of packaging film, agricultural film, the difficulty is sorting and removing impurities and attached to the thin film on the surface of other substances (dust, grease, paint, etc.).
(1) crushing
Large pieces of films are needed to be cut or grind into a piece of easy processing pieces. Crushing equipment has dry and wet points. Dry mill can be directly to the collection of the film to be crushed; wet mill will need to collect the film in the pre – cleaning and then smash. The former is simple in structure and small in investment, but because of the large thin film containing more impurities, the tool wear is larger; while the latter is increased a process, but the tool wear is small and the noise is low.
(2) cleaning
The purpose of cleaning is to remove other material attached to the surface of the film, so that the final recycling material has a higher purity and better performance. Usually wash with water, with the method of mixing the other material that is attached to the surface of the film. Using hot water washing or use of detergent to clean trong adhesion of the oil, ink, pigment.
(3) dehydration
After the cleaning of the film contain a large amount of water, in order to further processing and processing must be dehydrated. At present, the dehydration method mainly has the sieve dehydration and centrifugal dewatering. The film screen is dehydration after cleaning the debris to have certain requirements of the screen mesh, and the water film fragments separation. The form of the screen can be placed flat, or slant. A better screen dewatering effect with vibrator. Centrifugal dewatering machine is a high speed rotating centrifugal force generated by the strong centrifugal force to make the film debris dehydration.
(4) drying
After dehydration treatment, the film fragments still contain a certain amount of water, in order to reduce the moisture content to 0.5%, must be dry processing. Drying usually uses hot air dryers or heaters to save energy, reduce the cost, and the heat generated by the dryer or heater should be recycled.
(5) granulation
After washing and drying the film debris can be fed into the extruder granulation. In order to prevent the “bridge” phenomenon appears in the light of a large volume of film fragments (50g / L), the need for the feed screw pre compression, the material compaction, feed screw speed and extrusion machine matched, to prevent overload of the machine. By adding appropriate amount of auxiliary agent to improve the performance of the material.
In the process of melt extrusion of film fragments, often with water vapor, monomer decomposition gases produced. In order to make the production of pellets without air bubbles shall take venting measures. In addition, in order to get the high quality of the material, it is necessary to filter the material of the recycling material. Filtration can be filtered by the melt filtration can be retained after the filter. Melt filtration can be used in intermittent or continuous filter. Intermittent filter network will cause the interruption of the melt flow, every time after adjustment need to re adjust the process conditions, the replacement of the continuous filter will not interrupt the flow of the melt.
Recycling process and equipment were typical
The main characteristics of the device is the use of closed cylindrical horizontal cleaning device. The inner wall of the cylinder is equipped with a fixed number of blades, and the center of the mixing shaft is also equipped with a number of small holes in the blade, the speed of the mixing shaft is 300r/min, and the motor power is 7.5kW. All materials are transported by pipeline.
PE film recycling production line
The main characteristic of the device is the whole system without heating device. The broken pieces of the debris after a number of dehydration, and then crushed and dry in the mill. A crusher high-speed kneading machine, equipped with blade, using the friction heat generated to evaporate the water by the smashing.
Intco company developed a set of polyethylene recycling device see below, can handle the 3-4kt polyethylene plastic.
Leave a Reply